FR-830 PCB Underboard Heater

FeaturesCompact pre-heater with quick start-up and excellent heat recovery.Combined with HAKKO FR803B(SMD Rework Station)Easy attachment with connecting cord which is included in HAKKO FR803B Upgraded working efficiency by heating parts from top and bottom Operating FR820 with buttons of HAKKO FR803B (Start Ventilating/Cooling Down by pressing “HOT AIR” button on Handpiece of FR803B) Automatically cool down after turning off the powerTemperature regulating function Temperature range 150-300°C(302-572°F) CAL enables fine adjustment of temperature.Preheating in short time The improved air outlet shorten preheat time compared with air conventional product. * Please refer to above values, which vary depending on soldering condition. Hot air temperature 300°C A gap between the hot air outlet and the PWB for 10mm Attach sensors to top/under sides of P.W.B and measure temperature.Suitable for multi-layer board preheatingAutomatic cool-down function mounted. Pushing the “START/STOP” button at the end of work automatically activates the cool-down function.The FR830-13 PCB Underboard Heater has a compact, lightweight, and slightly larger hot air outlet. Various types of optional functions Local heating enabled. A set of [Extension pipe w/ Lid] is available. Various types of switching! [Hand switch][Foot switch] can be connected. Using the optional equipments HAKKO FR830-13 PCB Underboard Heater Omnivise C1390C (2 used) (Rework system) Extension pipe/with backflow prevention lid B3263 (option)Extension pipe:Used for localized heatingBackflow prevention lid:When using in combination with SMD rework hot air, use the lid so hot air does not flow back into the FR-830 hot air outlet. Note Always use the backflow prevention lid when the FR830 switch is off. Set example HAKKO FR830-13 PCB Underboard Heater SMD rework station HAKKO FR803B (discontinued) Rework fixture C1392B* Omnivise C1390C* (2 used) *Rework system Various types of switching! [Hand switch][Foot switch] can be connected. Hand switchConnection cord length: Approximately 100 cm Switch size: Approx. 30mm (W) / 40mm (D) / 20mm (H)When using the hand switch, switching is not possible on the main device.Foot switchConnection cord length: Approximately 135 cmWhen using the foot switch, switching is not possible on the main device.Controlling the temperatures of Hot Air Rework System and workpiece using the Temperature Probe Measure temperatures of Hot Air Rework System and workpiece using the Temperature Probe for Hot Air Rework System (No. C1541) and thermometer (HAKKO FG-100/HAKKO FG-101) to protect the workpiece. * Please refer to above values, which vary depending on soldering condition.Measuring conditionHot air temperature 300°C A gap between the hot air outlet and the PWB for 10mm Attach sensors to top/under sides of P.W.B and measure temperature.Usage/ApplicationsPlease keep a gap between the hot air outlet and the PWB for more than10mmto allow the air to flow. When there is not enough space for the air to flow, the fuse may blow up. How to useWhen should the optional Temperature Probe for Hot Air Rework System(No. C1541) be usedThe Temperature Probe for Hot Air Rework System (No. C1541) is equipped with 2 types of sensors. Before measuring temperatures as follows, connect the sensor to the thermometer.Sensor A:When measuring the temperature of hot air blown from the nozzle: Correcting thermal control can be made by confirming the temperature of the hot air that is actually blown.Sensor B:When measuring the temperature of applicable parts (workpieces): Rework can be performed without causing damage to the parts being reworked (QFP, etc.) Categories: HAKKO, Pre-heaters, Product catalogue, Shop by brand, SMD rework Tags: FG100, FG101, FR803, FR830, FR830-13, Underboard Heater